Auto-page C3-RS1100 Bedienungsanleitung

C3 RS1100REV. A 1 C3-RS1100 OLED PROFESSIONAL 2-WAY 915 MHz. OLED REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Temperature Sensor

C3 RS1100REV. A 10 H6: 22 PIN WIRE CONNECTORS: H6/1 BROWN/BLACK WIRE: 200 mA (-) Ground Output When Running. This wire provides a negative output d

C3 RS1100REV. A 11This output is for a Key Sense wire by -pass that some Chrysler and Toyota vehicles need to activate remote start. This wire comes o

C3 RS1100REV. A 12When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is di

C3 RS1100REV. A 13Also on certain BMW, Mercedes Benz, Jaguar and Volkswagen cars, you can use this unique timed output to allow remote closure of all

C3 RS1100REV. A 14This wire provides a 200mA (-) ground output that becomes active 4 seconds before the remote start unit initialize, and remains grou

C3 RS1100REV. A 15To + 12 VIgnitionSwitchYELLOW wireMatching ResistorVATS control Module87a86308785VAT wire (#1)VAT wire(#2) H6/15 Green wire – Neg

C3 RS1100REV. A 16The WHITE/BLACK wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire to the hood pin s

C3 RS1100REV. A 17 VACUUM OPERATED CENTRAL LOCKING Green Wire Blue Wire +12V X Cut Compressor Door Switch 30 86 87a 85 87 30 86 87a85 87 3 Pin Plug T

C3 RS1100REV. A 182 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS Cut Existing Unlock X Lock Unlock OEM Door Master Lock Switch To A

C3 RS1100REV. A 194. Press the transmitter button corresponding to the feature you want to program. Press Transmitter Button One Chirp / LED one pul

C3 RS1100REV. A 2 TABLE OF CONTENTS: INSTALLATION DIAGRAMS 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION 6 H1/1 Violet Wire – Starter Output 6 H1/2

C3 RS1100REV. A 201 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 5 times (holding in on the 5th pus

C3 RS1100REV. A 21(The system Can not be Arm with the engine running) The shock sensor will be by-passed upon engine running. (The engine will run b

C3 RS1100REV. A 222 H6/6 Brown / White Wire = (-) 200mA Horn Output H6/6 Brown / White Wire = Factory Security Rearm Signal Output 3 Fahrenheit

C3 RS1100REV. A 23Note 1 : If your built-in timer controls window/sunroof closure in your car DO NOT change the timer setting! This requires installer

C3 RS1100REV. A 24Program: 1. Press and release the transmitter button twice, [2] LED flash, [2] siren/horn chirp to indicate you are in features “

C3 RS1100REV. A 256 + Temperature- Control Starting OFF Temperature-Control Starting “ON” 0 ºF / -18 ºC Temperature-Control Starting “ON” 15 ºF

C3 RS1100REV. A 266 + “TEST” Mode for Zone 2 / instant tri gger & Zone 3 / Door trigger “TEST” Mode for Zone 1 & Zone 4 (2 Stage Shock Se

C3 RS1100REV. A 27 CHECK LEVEL PROGRAMMING: (TEST and ADJUST) 1. Press button once on the transmitter to start the vehicle. 2. If everything goes w

C3 RS1100REV. A 28b. Press button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm entry. (Increase “Start T

C3 RS1100REV. A 29 b. Test the Zone 1 & Zone 4 / Two S tage Shock Sensor (Connected to H9 4 Pin Plug): Press and release the transmitter and

C3 RS1100REV. A 3Mechanical Neutral Safety Switch Considerations 31 Park/Neutral ECM Input 31 Key In Sensor Circuits 32 INTRODUCTION This Remote

C3 RS1100REV. A 305. The remote start feature programming has not been programmed to start the vehicle. The remote start must be programmed how to st

C3 RS1100REV. A 313. NEUTRAL START SAFETY TEST: 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. Sitting

C3 RS1100REV. A 32 Ignition P 12DNRElectronic Control Module (ECM) Solid State, Do Not Measure Resistance To Neutral Safety Switch Input wir

C3 RS1100REV. A 33(H6/8) of the Remote Start Unit. F. Connect terminal 86 of the relay to a fused + 12 volt constant battery source. G. Connect term

C3 RS1100REV. A 34 Available At an Authorized Autopage Dealer The RS-1100 is CI3 Compatible It is recommended to have a minimal digital service pla

C3 RS1100REV. A 35 BLANK PAGE

C3 RS1100REV. A 36 960 Knox Street Unit B Torrance, California 90502 Main Office: 310-323-1800 Technical Support: 800-945-252

C3 RS1100REV. A 37www.autopageusa.com 2-Way Communication to the Power of 3

C3 RS1100REV. A 4 INSTALLATION DIAGRAM

C3 RS1100REV. A 520A20ARed: Remote Start Power 1Red: Remote Start Power 2Violet: Starter (+) OutputPink: Ignition 2 (+) OutputYellow: Ignition 1 (+) O

C3 RS1100REV. A 6 WIRING Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Be sure to tape wires that pass throug

C3 RS1100REV. A 7 Red Wire (2) — +12V Power Input Remove the two 20A fuses prior to connecting these wires and do not replace them until the satellite

C3 RS1100REV. A 8been designed for use with all C I 3 compatible components. C I 3 Telematics system is available at any authorized Autopage dealer.

C3 RS1100REV. A 9 H7. 4-PIN BLACK CONNECTOR. – TWO-WAY TRANSCEIVER/ANTENNA MODULE The Two-way transceiver/antenna mounting location should be the uppe